Extreme 100G-QSFP28-SR4-I Compatible 100G QSFP28 SR4 Transceiver Module
The 100G-QSFP28-SR4-I compatible module serves equipment requiring a 100G QSFP28 interface with 850nm optics and a 70m on OM3 / 100m on OM4 rating. Connection is through MTP/MPO-12 Male. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: 100G-QSFP28-SR4-IHT Part Number: QSFP-SR4-100G-I
Product Highlights
- Compatible alternative to Extreme 100G-QSFP28-SR4-I
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 850nm
- Specified reach: 70m on OM3 / 100m on OM4
- MTP/MPO-12 Male / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| Extreme Compatible | 100G-QSFP28-SR4-I |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-SR4-100G-I |
| Form Factor | QSFP28 |
| Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 850nm |
| Max Cable Distance | 70m@OM3/100m@OM4 |
| Connector | MTP/MPO-12 Male |
| Media | MMF |
| Transmitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -6~2.4dBm |
| RX Power | -10.3~ 2.4dBm |
| Power Budget | 4.3dB |
| Extinction Ratio | ＞2dB |
| Typical Power Consumption | <2.5W |
| DDM/DOM | Supported |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Packaging Technology | COB Packaging |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | No |
| Bit Error Ratio (BER) | 1E-12 |
| MTBF | 1,160,000 Hours |
| Protocols | IEEE 802.3bm, QSFP28 MSA, SFF-8665, SFF-8636, RoHS, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 850nm, rated reach 70m on OM3 / 100m on OM4.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 Male interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 70m on OM3 / 100m on OM4 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-12 Male mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6~2.4dBm; the stated optical power budget is 4.3dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each 100G-QSFP28-SR4-I compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Extreme Compatibility and Factory Testing
The module is checked for host recognition as 100G-QSFP28-SR4-I, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Extreme transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 100G-QSFP28-SR4-I, not an original Extreme-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 Male with MMF. The specified maximum reach is 70m on OM3 / 100m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP-SR4-100G-I together with OEM reference 100G-QSFP28-SR4-I and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
