Extreme Networks 10340 Compatible 10G SFP+ SGMII T Transceiver Module
Built for hosts recognizing 10340, this HT-manufactured SFP+ SGMII module delivers 10G transmission at the listed wavelength plan. Its rated reach is 100m on Cat6a / Cat7, with RJ-45 as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 10340HT Part Number: SFP-10G-T-100
Product Highlights
- Compatible alternative to Extreme Networks 10340
- 10G connectivity at 10Gbps
- Specified reach: 100m on Cat6a / Cat7
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-10G-T-100 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ SGMII |
| Max. Data Rate | 10Gbps |
| Max. Power Consumption | ≤1.8W |
| Max. Transmission Distance | 100m@Cat6a/Cat7 |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Supported (Manual Configuration) |
| MTBF | 4,790,000 Hours |
| EMC (Electro Magnetic Compatibility) | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3az, IEEE 802.3-2012, SFF-8472, SFF-8432, SFP+ MSA |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, rated reach 100m on Cat6a / Cat7.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ SGMII housing alone does not make two transceiver types interoperable.
The rated 100m on Cat6a / Cat7 copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Extreme Networks Compatibility and Factory Testing
Factory verification starts with the expected 10340 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 10340, not an original Extreme Networks-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 100m on Cat6a / Cat7, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
Quote HT part number SFP-10G-T-100 together with OEM reference 10340 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
