Brocade 10G-SFPP-BXD-60K Compatible 10G SFP+ BX60-D Transceiver Module
The 10G-SFPP-BXD-60K compatible module serves equipment requiring a 10G SFP+ interface with 1330nm-TX/1270nm-RX optics and a 60km rating. Connection is through Simplex LC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: 10G-SFPP-BXD-60KHT Part Number: 10G-SFPP-BXD-60K
Product Highlights
- Compatible alternative to Brocade 10G-SFPP-BXD-60K
- 10G connectivity at 10Gbps
- Optical wavelength: 1330nm-TX/1270nm-RX
- Specified reach: 60km
- Simplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | 10G-SFPP-BXD-60K |
|---|---|
| Manufacturer | HT |
| HT Part Number | 10G-SFPP-BXD-60K |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1330nm-TX/1270nm-RX |
| Max. Transmission Distance | 60km |
| Connector | Simplex LC |
| Transmitter Type | DFB BiDi |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 1~6dBm |
| Receiver Sensitivity | <-20dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI, 10GBASE-ZR |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1330nm-TX/1270nm-RX, rated reach 60km.
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
This single-fiber interface must be paired with the complementary wavelength direction. One end transmits on the wavelength the other receives. Verify connector polish and measure loss over the 60km design range before service.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 1~6dBm; receiver sensitivity is <-20dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each 10G-SFPP-BXD-60K compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Brocade Compatibility and Factory Testing
Compatibility testing for 10G-SFPP-BXD-60K combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 10G-SFPP-BXD-60K, not an original Brocade-branded module.
Which fiber and connector are required?
Use Simplex LC with SMF. The specified maximum reach is 60km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify 10G-SFPP-BXD-60K, 10G-SFPP-BXD-60K, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
