Ciena 180-3360-900 Compatible 400G QSFP-DD Transceiver Module
Built for hosts recognizing 180-3360-900, this HT-manufactured QSFP-DD module delivers 400G transmission at 1528.58-1567.54nm. Its rated reach is 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 180-3360-900HT Part Number: QDD-ZRPH-400GM
Product Highlights
- Compatible alternative to Ciena 180-3360-900
- 400G connectivity at 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+
- Optical wavelength: 1528.58-1567.54nm
- Specified reach: 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Support
- Operating temperature: 0℃ to 75°C
Specifications
| Ciena Compatible | 180-3360-900 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QDD-ZRPH-400GM |
| Form Factor | QSFP-DD |
| Data Rate | 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+ |
| Wavelength | 1528.58-1567.54nm |
| Distance | 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| TX Power Range | -7~4dBm |
| RX Power Range | ＜1.5dB ROSNR penalty: -12~-6dBm ＜0.5dB ROSNR penalty: -6~5dBm OTN STD: -21~5dBm |
| Power Consumption | 19.3W |
| CD Tolerance | 400G ZR：-2.4~2.4 ns/nm 400G ZR+：-60~60 ns/nm |
| DDM/DOM | Support |
| Commercial Temperature Range | 0℃ to 75°C |
| FEC | OFEC, CFEC, SFEC |
| Modulation Format | QPSK/16QAM |
| Protocols | Open ZR+ MSA R1.0 and OTN，OIF 400ZR OIF-400ZR-01.0 and IEEE802.3cw R2.3 coherent standard, CMIS Rev 5.0, OIF C-CMIS 1.1 |
| Application | LH/Regional/Metro/ROADMs |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+, wavelength 1528.58-1567.54nm, rated reach 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km.
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Support. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Ciena Compatibility and Factory Testing
Compatibility testing for 180-3360-900 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Ciena transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 180-3360-900, not an original Ciena-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QDD-ZRPH-400GM together with OEM reference 180-3360-900 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
