Brocade 1G-SFP-ZRD-1563.86-100 Compatible 1G SFP Transceiver Module
Built for hosts recognizing 1G-SFP-ZRD-1563.86-100, this HT-manufactured SFP module delivers 1G transmission at 1563.86nm. Its rated reach is 100km, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 1G-SFP-ZRD-1563.86-100HT Part Number: DW-SFP1G100-17
Product Highlights
- Compatible alternative to Brocade 1G-SFP-ZRD-1563.86-100
- 1G connectivity at 1000Mbps
- Optical wavelength: 1563.86nm
- Specified reach: 100km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | 1G-SFP-ZRD-1563.86-100 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP1G100-17 |
| Form Factor | SFP |
| Max Data Rate | 1000Mbps |
| Wavelength | 1563.86nm |
| Max Cable Distance | 100km |
| Connector | Duplex LC |
| Optical Components | EML DWDM |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 0~5dBm |
| Receiver Sensitivity | < -32dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | MSA Compliant |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1000Mbps, wavelength 1563.86nm, rated reach 100km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1563.86nm, then include their insertion loss in the 100km power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -32dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each 1G-SFP-ZRD-1563.86-100 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Brocade Compatibility and Factory Testing
Compatibility testing for 1G-SFP-ZRD-1563.86-100 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 1G-SFP-ZRD-1563.86-100, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 100km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify 1G-SFP-ZRD-1563.86-100, DW-SFP1G100-17, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
