Dell Networking 330-2404-40 Compatible 10G SFP+ ER Transceiver Module
The 330-2404-40 compatible module serves equipment requiring a 10G SFP+ interface with 1310nm optics and a 40km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: 330-2404-40HT Part Number: SFP-10GER-31
Product Highlights
- Compatible alternative to Dell Networking 330-2404-40
- 10G connectivity at 11.3Gbps
- Optical wavelength: 1310nm
- Specified reach: 40km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Dell Compatible | 330-2404-40 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GER-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 40km |
| Connector | Duplex LC |
| Transmitter Type | DFB 1310nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 0~5dBm |
| Receiver Sensitivity | <-15dBm |
| Core Size | 9/125µm |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 11.3Gbps, wavelength 1310nm, rated reach 40km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 40km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is <-15dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Dell Networking Compatibility and Factory Testing
Factory verification starts with the expected 330-2404-40 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Dell Networking transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 330-2404-40, not an original Dell Networking-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify 330-2404-40, SFP-10GER-31, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
