Brocade 40G-QSFP-LM4 Compatible 40G QSFP+ LM4 Transceiver Module
The 40G-QSFP-LM4 compatible module serves equipment requiring a 40G QSFP+ interface with 1310nm optics and a 150m on OM3 / 2km on SMF rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: 40G-QSFP-LM4HT Part Number: QSFP-LX4-40G
Product Highlights
- Compatible alternative to Brocade 40G-QSFP-LM4
- 40G connectivity at 41.2Gbps (4x 10.3Gbps)
- Optical wavelength: 1310nm
- Specified reach: 150m on OM3 / 2km on SMF
- Duplex LC / MMF/SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | 40G-QSFP-LM4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-LX4-40G |
| Form Factor | QSFP+ |
| Max. Data Rate | 41.2Gbps (4x 10.3Gbps) |
| Wavelength | 1310nm |
| Max. Transmission Distance | 150m@OM3/2km@SMF |
| Connector | Duplex LC |
| Media | MMF/SMF |
| Transimitter Type | CWDM4 DFB |
| Receiver Type | PIN |
| TX Power | -5~3.5dBm |
| Receiver Sensitivity (OMA) | <-10.5dBm |
| Receiver Overload | 3.5dB |
| Power Budget | 5.5 dB |
| Max. Power Consumption | ≤3.5W |
| Extinction Ratio | >3.5dB |
| Host FEC | Supported |
| Bit Error Ratio (BER) | 1E-12 |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | 40G Ethernet, MSA Compliant |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 41.2Gbps (4x 10.3Gbps), wavelength 1310nm, rated reach 150m on OM3 / 2km on SMF.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 40G interface configuration must match the remote equipment; sharing a QSFP+ housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m on OM3 / 2km on SMF reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -5~3.5dBm; the stated optical power budget is 5.5 dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Brocade Compatibility and Factory Testing
Factory verification starts with the expected 40G-QSFP-LM4 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 40G-QSFP-LM4, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF/SMF. The specified maximum reach is 150m on OM3 / 2km on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP-LX4-40G together with OEM reference 40G-QSFP-LM4 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
