Juniper Networks 40G-SR4 Compatible 40G QSFP+ SR4 Transceiver Module
Built for hosts recognizing 40G-SR4, this HT-manufactured QSFP+ module delivers 40G transmission at 850nm. Its rated reach is 150m on OM4 / 100m on OM3, with MTP/MPO-12 Male as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 40G-SR4HT Part Number: QSFP-SR4-40G-I
Product Highlights
- Compatible alternative to Juniper Networks 40G-SR4
- 40G connectivity at 41.25Gbps (4x 10.3125Gbps)
- Optical wavelength: 850nm
- Specified reach: 150m on OM4 / 100m on OM3
- MTP/MPO-12 Male / MMF interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-SR4-40G-I |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP+ |
| Max. Data Rate | 41.25Gbps (4x 10.3125Gbps) |
| Wavelength | 850nm |
| Max. Transmission Distance | 150m@OM4/100m@OM3 |
| Connector | MTP/MPO-12 Male |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.6~2.4dBm |
| Receiver Sensitivity | ＜-9.5dBm |
| Power Budget | 1.9dB |
| Receiver Overload | 2.4dBm |
| Max. Power Consumption | ≤1.5W |
| Extinction Ratio | >3dB |
| Host FEC | Supported |
| Bit Error Ratio (BER) | 1E-12 |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
| Protocols | IEEE 802.3ba, QSFP+ MSA, SFF-8436 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 41.25Gbps (4x 10.3125Gbps), wavelength 850nm, rated reach 150m on OM4 / 100m on OM3.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 Male interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 150m on OM4 / 100m on OM3 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-12 Male mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.6~2.4dBm; receiver sensitivity is ＜-9.5dBm; the stated optical power budget is 1.9dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected 40G-SR4 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 40G-SR4, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 Male with MMF. The specified maximum reach is 150m on OM4 / 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use 40G-SR4 as the compatibility cross-reference and QSFP-SR4-40G-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
