Juniper Networks CFP2-100G-LR4-D Compatible 100G CFP2 LR4 Transceiver Module
Built for hosts recognizing CFP2-100G-LR4-D, this HT-manufactured CFP2 module delivers 100G transmission at 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm. Its rated reach is 10km, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CFP2-100G-LR4-DHT Part Number: CFP2-LR4-100G
Product Highlights
- Compatible alternative to Juniper Networks CFP2-100G-LR4-D
- 100G connectivity at 112Gbps
- Optical wavelength: 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | CFP2-LR4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | CFP2 |
| Max Data Rate | 112Gbps |
| Wavelength | 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm |
| Max Cable Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Optical Components | 4x DFB |
| Extinction Ratio | ＞4dB |
| TX Power | -4.3~4.5dBm |
| RX Power | -10.6~4.5dBm |
| Typical Power Consumption | 6W |
| Core Size | 9/125 um |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Protocols | CFP2 MSA, IEEE 802.3ba 100GBASE-LR4 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 112Gbps, wavelength 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm, rated reach 10km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP2 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 10km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.3~4.5dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each CFP2-100G-LR4-D compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as CFP2-100G-LR4-D, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CFP2-100G-LR4-D, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use CFP2-100G-LR4-D as the compatibility cross-reference and CFP2-LR4-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
