HPE CWDM-SFP10G-1470 Compatible 10G SFP+ Transceiver Module 40km
This HPE CWDM-SFP10G-1470 compatible transceiver provides 10G connectivity in a hot-swappable SFP+ package. Its optical design operates at 1470nm for up to 40km, using Duplex LC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: CWDM-SFP10G-1470HT Part Number: CWDM-SFP10G-40L
Product Highlights
- Compatible alternative to HPE CWDM-SFP10G-1470
- 10G connectivity at 10Gbps
- Optical wavelength: 1470nm
- Specified reach: 40km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HPE Compatible | CWDM-SFP10G-1470 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CWDM-SFP10G-40L |
| Form Factor | SFP+ |
| Max Data Rate | 10Gbps |
| Wavelength | 1470nm |
| Max Cable Distance | 40km |
| Connector | Duplex LC |
| Media | SMF |
| Power Consumption | 1W |
| Packaging Technology | BOX |
| Optical Components | EML CWDM |
| DOM Support | Yes |
| TX Power | -1~4dBm |
| RX Power | -16~0dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Receiver Sensitivity | <-16dBm |
| Modulation | NRZ |
| Extinction Ratio | >3.5dB |
| Protocols | SFP+ MSA Compliant, SFF 8472,SFF 8431,802.3ae, ITU-T |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1470nm, rated reach 40km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1470nm, then include their insertion loss in the 40km power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; receiver sensitivity is <-16dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
HPE Compatibility and Factory Testing
Factory verification starts with the expected CWDM-SFP10G-1470 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original HPE transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CWDM-SFP10G-1470, not an original HPE-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify CWDM-SFP10G-1470, CWDM-SFP10G-40L, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
