Cisco CXP-100G-SR10 Compatible 100G CXP SR10 Transceiver Module
The CXP-100G-SR10 compatible module serves equipment requiring a 100G CXP interface with 850nm optics and a 150m on OM4, 100m on OM3 rating. Connection is through MTP/MPO-24. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: CXP-100G-SR10HT Part Number: CXP-SR10-100G
Product Highlights
- Compatible alternative to Cisco CXP-100G-SR10
- 100G connectivity at 120 Gbp
- Optical wavelength: 850nm
- Specified reach: 150m on OM4, 100m on OM3
- MTP/MPO-24 / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Cisco Compatible | CXP-100G-SR10 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CXP-SR10-100G |
| Form Factor | CXP |
| Max Data Rate | 120 Gbp |
| Wavelength | 850nm |
| Max Cable Distance | 150m@OM4, 100m@OM3 |
| Connector | MTP/MPO-24 |
| Media | MMF |
| Optical Components | 10x VCSEL |
| Extinction Ratio | >3dB |
| TX Power | -7.6~2.4dBm |
| RX Power | -9.5~2.4dBm |
| Typical Power Consumption | <3.5W |
| Core Size | 50/125μm |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 10x 10G-NRZ |
| Modulation (Optical) | 10x 10G-NRZ |
| Protocols | MSA Compliant |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 120 Gbp, wavelength 850nm, rated reach 150m on OM4, 100m on OM3.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-24 interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CXP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m on OM4, 100m on OM3 reach. Keep the MTP/MPO-24 end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.6~2.4dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
Compatibility testing for CXP-100G-SR10 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CXP-100G-SR10, not an original Cisco-branded module.
Which fiber and connector are required?
Use MTP/MPO-24 with MMF. The specified maximum reach is 150m on OM4, 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify CXP-100G-SR10, CXP-SR10-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
