Juniper Networks EX-SFP-1GE-SX-ET Compatible 1G SFP Transceiver Module
Built for hosts recognizing EX-SFP-1GE-SX-ET, this HT-manufactured SFP module delivers 1G transmission at 850nm. Its rated reach is 550m over OM2 MMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: EX-SFP-1GE-SX-ETHT Part Number: SFP1G-SX-85-I
Product Highlights
- Compatible alternative to Juniper Networks EX-SFP-1GE-SX-ET
- 1G connectivity at 1.25Gbps
- Optical wavelength: 850nm
- Specified reach: 550m over OM2 MMF
- Duplex LC / MMF interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | EX-SFP-1GE-SX-ET |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP1G-SX-85-I |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 550m over OM2 MMF |
| Connector | Duplex LC |
| Optical Components | VCSEL 850nm |
| Media | MMF |
| DOM Support | Yes |
| TX Power | -9.5~-3dBm |
| Receiver Sensitivity | < -17dBm |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | IEEE 802.3z, SFF-8472, FC-PI, SFP MSA (INF-8074i) Compliant |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1.25Gbps, wavelength 850nm, rated reach 550m over OM2 MMF.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 550m over OM2 MMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9.5~-3dBm; receiver sensitivity is < -17dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
Compatibility testing for EX-SFP-1GE-SX-ET combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies EX-SFP-1GE-SX-ET, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 550m over OM2 MMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify EX-SFP-1GE-SX-ET, SFP1G-SX-85-I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
