Fortinet FN-CABLE-SFP56-DAC-L1 Compatible 50G SFP56 Passive Copper Twinax Cable, 1m (3ft)
For a direct equipment connection requiring Fortinet FN-CABLE-SFP56-DAC-L1, this page supplies the 1m (3ft) version with SFP56 to SFP56. The cable supports 50G operation and eliminates a separate module-and-patch-cord assembly. Installation, maintenance and spare-cable identification are addressed alongside the full technical details.
OEM Part Number: FN-CABLE-SFP56-DAC-L1HT Part Number: FN-CABLE-SFP56-DAC-L1
Product Highlights
- Compatible alternative to Fortinet FN-CABLE-SFP56-DAC-L1
- 50G connectivity at 50Gbps
- Interface configuration: SFP56 to SFP56
- Fixed length and part number: 1m (3ft), FN-CABLE-SFP56-DAC-L1
- Cable construction: Passive Twinax
- Conductor specification: 30AWG
- Maximum power consumption: ＜0.1W
Specifications
| HT Part Number | FN-CABLE-SFP56-DAC-L1 |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP56 to SFP56 |
| Max Data Rate | 50Gbps |
| Cable Length | 1m(3ft) |
| Wire AWG | 30AWG |
| Power Consumption | ＜0.1W |
| Jacket Material | PVC |
| Cable Type | Passive Twinax |
| Compatible | Generic |
| Temperature | 0°C to 70°C (32 to 158°F) |
| Application | 50G Ethernet |
| Modulation Technology | PAM4 |
| Protocol | SFP28 MSA SFF-8432 |
Power and Thermal Planning
The rated power consumption is ＜0.1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Length Selection and Installation Planning
At 1m (3ft), FN-CABLE-SFP56-DAC-L1 is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the listed conductor specification is 30AWG; the stated power consumption is ＜0.1W; the jacket material is PVC.
Cable Construction and Routing
This assembly uses 30AWG conductors, PVC jacket. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is 50G Ethernet.
Passive Copper Operation
A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Neutral packaging and customer-specific packing documentation are available on request.
Fortinet Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. Where supported by the host, link stability and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original Fortinet cable?
No. It is an HT-manufactured compatible alternative for equipment that specifies Fortinet FN-CABLE-SFP56-DAC-L1.
Does this order code cover multiple lengths?
No. FN-CABLE-SFP56-DAC-L1 refers here to 1m (3ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. This page’s fixed configuration is 1m (3ft); another length must be quoted under its corresponding part number.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.
