Cisco GLC-FE-T Compatible 100M SFP SGMII Transceiver Module
The GLC-FE-T compatible module serves equipment requiring a 100M SFP SGMII interface with the listed wavelength plan optics and a 100m rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: GLC-FE-THT Part Number: SFP-FB-GE-T
Product Highlights
- Compatible alternative to Cisco GLC-FE-T
- 100M connectivity at 100Mbps
- Specified reach: 100m
- RJ-45 / Cat 5/Cat 6/Cat 6a interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| Cisco Compatible | GLC-FE-T |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-FB-GE-T |
| Form Factor | SFP SGMII |
| Max. Data Rate | 100Mbps |
| Media | Cat 5/Cat 6/Cat 6a |
| Max. Cable Distance | 100m |
| Connector | RJ-45 |
| DOM Support | No |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | SFP+ MSA Compliant, SFF-8472, IEEE 802.3ae, FC-PI-5, SFF-8431 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 100Mbps, rated reach 100m.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100M interface configuration must match the remote equipment; sharing a SFP SGMII housing alone does not make two transceiver types interoperable.
The rated 100m copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as GLC-FE-T, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies GLC-FE-T, not an original Cisco-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Cat 5/Cat 6/Cat 6a. The rated reach is 100m, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
Quote HT part number SFP-FB-GE-T together with OEM reference GLC-FE-T and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
