HPE Aruba J9152D Compatible 10.3125G SFP+ 10GBASE-LRM Transceiver Module
Built for hosts recognizing J9152D, this HT-manufactured SFP+ module delivers 10.3125G transmission at 1310nm. Its rated reach is 220m, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: J9152DHT Part Number: SFP-10GLRM-31
Product Highlights
- Compatible alternative to HPE Aruba J9152D
- 10.3125G connectivity at 10.3125Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HPE Aruba Compatible | J9152D |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRM-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | FP |
| Receiver Type | PIN |
| TX Power | -6~-1dBm |
| Receiver Sensitivity | <-10dBm |
| Power Budget | 4dB |
| Receiver Overload | 1.5dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3.5dB |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| DDM/DOM | Supported |
| Core Size | 50/125µm@OM3 MMF |
| Modulation | NRZ |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1310nm, rated reach 220m.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10.3125G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 220m figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6~-1dBm; receiver sensitivity is <-10dBm; the stated optical power budget is 4dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each J9152D compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
HPE Aruba Compatibility and Factory Testing
Compatibility testing for J9152D combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original HPE Aruba transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies J9152D, not an original HPE Aruba-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 220m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use J9152D as the compatibility cross-reference and SFP-10GLRM-31 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
