Juniper JNP-SFPP-10GE-T Compatible 10G SFP+ Transceiver Module
The JNP-SFPP-10GE-T compatible module serves equipment requiring a 10G SFP+ interface with the listed wavelength plan optics and a 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: JNP-SFPP-10GE-THT Part Number: SFP-10GM-T-30
Product Highlights
- Compatible alternative to Juniper JNP-SFPP-10GE-T
- 10G connectivity at 10.3125Gbps
- Specified reach: 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| Juniper Compatible | JNP-SFPP-10GE-T |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GM-T-30 |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Max. Power Consumption | ≤2.5W |
| Max. Transmission Distance | 10/100/1000M-100m@Cat 5 Cable or better10G-30m@Cat 6a/7 Cable |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Supported (Auto-negotiation) |
| MTBF | 6430000 Hours |
| EMC (Electro Magnetic Compatibility) | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3az SFP+ MSA |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10.3125Gbps, rated reach 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
The rated 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Compatibility and Factory Testing
Factory verification starts with the expected JNP-SFPP-10GE-T identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies JNP-SFPP-10GE-T, not an original Juniper-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
Quote HT part number SFP-10GM-T-30 together with OEM reference JNP-SFPP-10GE-T and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
