NVIDIA/Mellanox MMS4A20-XM800 Compatible 800G Single-port OSFP RHS/Flat Top DR4 Transceiver Module
This NVIDIA/Mellanox MMS4A20-XM800 compatible transceiver provides 800G connectivity in a hot-swappable Single-port OSFP RHS/Flat Top package. Its optical design operates at 1310nm for up to 500m, using MPO-12/APC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: MMS4A20-XM800HT Part Number: OSFP224-DR4-800G-FL
Product Highlights
- Compatible alternative to NVIDIA/Mellanox MMS4A20-XM800
- 800G connectivity at 850Gbps (4x 212.5Gbps)
- Optical wavelength: 1310nm
- Specified reach: 500m
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| NVIDIA/Mellanox InfiniBand Compatible | MMS4A20-XM800 |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP224-DR4-800G-FL |
| Form Factor | Single-port OSFP RHS/Flat Top |
| Max. Data Rate | 850Gbps (4x 212.5Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 500m |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | CW (SiPh-Based) |
| Receiver Type | PIN |
| TX Power | -3.3~4dBm |
| Minimum Receiver Power | -6.3dBm |
| Power Budget | 3dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 16W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 200G-PAM4 |
| Modulation (Optical) | 4x 200G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Inbuilt FEC | No |
| Packaging Technology | COB (Chip on Board) Packaging |
| Bit Error Ratio (BER) | 1E-12(FEC Enabled) |
| Protocols | OSFP MSA, CMIS Rev 5.2, IEEE 802.3dj, OIF 224G-VSR |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 850Gbps (4x 212.5Gbps), wavelength 1310nm, rated reach 500m.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Single-port OSFP RHS/Flat Top housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 500m route. Keep the MPO-12/APC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.3~4dBm; the stated optical power budget is 3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each MMS4A20-XM800 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
NVIDIA/Mellanox Compatibility and Factory Testing
Factory verification starts with the expected MMS4A20-XM800 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies MMS4A20-XM800, not an original NVIDIA/Mellanox-branded module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 500m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify MMS4A20-XM800, OSFP224-DR4-800G-FL, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
