Arista Networks OSFP-400G-VSR4 Compatible 400G OSFP (IHS/Finned Top) VSR4 Transceiver Module
The OSFP-400G-VSR4 compatible module serves equipment requiring a 400G OSFP (IHS/Finned Top) interface with 850nm optics and a 30m on OM3 / 50m on OM4 or OM5 rating. Connection is through MPO-12/APC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: OSFP-400G-VSR4HT Part Number: OSFP-VSR4-400G
Product Highlights
- Compatible alternative to Arista Networks OSFP-400G-VSR4
- 400G connectivity at 400Gbps
- Optical wavelength: 850nm
- Specified reach: 30m on OM3 / 50m on OM4 or OM5
- MPO-12/APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Arista Networks Compatible | OSFP-400G-VSR4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP-VSR4-400G |
| Form Factor | OSFP (IHS/Finned Top) |
| Max. Data Rate | 400Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 30m@OM3/50m@OM4 or OM5 |
| Connector | MPO-12/APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -4.6~4dBm |
| Minimum Receiver Power | -6.4dBm |
| Power Budget | 1.8dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 2.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | No |
| Bit Error Ratio (BER) | <2.4E-4 |
| MTBF | 684931 Hours (@50°C, 60% CL)273972 Hours (@50°C, 90% CL) |
| Packaging Technology | COB (Chip on Board) Packaging |
| Application | 400G Ethernet |
| Protocols | CMIS 5.2, IEEE 802.3bs-400GAUI-8, OSFP MSA, IEEE 802.3 db-400GBASE-VR4 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 400Gbps, wavelength 850nm, rated reach 30m on OM3 / 50m on OM4 or OM5.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a OSFP (IHS/Finned Top) housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 30m on OM3 / 50m on OM4 or OM5 reach. Keep the MPO-12/APC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6~4dBm; the stated optical power budget is 1.8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Arista Networks Compatibility and Factory Testing
Factory verification starts with the expected OSFP-400G-VSR4 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-400G-VSR4, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use MPO-12/APC with MMF. The specified maximum reach is 30m on OM3 / 50m on OM4 or OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number OSFP-VSR4-400G together with OEM reference OSFP-400G-VSR4 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
