Arista Networks OSFP-800G-2FR4 Compatible 800G Twin-port OSFP IHS/Closed Finned Top Transceiver Module
The OSFP-800G-2FR4 compatible module serves equipment requiring a 800G Twin-port OSFP IHS/Closed Finned Top interface with 1271nm, 1291nm, 1311nm and 1331nm optics and a 2km rating. Connection is through Dual Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: OSFP-800G-2FR4HT Part Number: OSFP-2FR4-800G
Product Highlights
- Compatible alternative to Arista Networks OSFP-800G-2FR4
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 2km
- Dual Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Arista Compatible | OSFP-800G-2FR4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP-2FR4-800G |
| Form Factor | Twin-port OSFP IHS/Closed Finned Top |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max Cable Distance | 2km |
| Connector | Dual Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -3.2~4.4dBm |
| Minimum Receiver Power | -7.2dBm |
| Power Budget | 4dB |
| Receiver Overload | 4.4dBm |
| Max Power Consumption | 16.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | Dual 4x100G-PAM4 |
| Protocols | OSFP MSA HW Rev 4.1, CMIS Rev 5.0, IEEE 802.3cu-2021, IEEE P802.3ck D2.2 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 2km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 2km route. Keep the Dual Duplex LC/UPC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.2~4.4dBm; the stated optical power budget is 4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each OSFP-800G-2FR4 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Arista Networks Compatibility and Factory Testing
The module is checked for host recognition as OSFP-800G-2FR4, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-800G-2FR4, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use Dual Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify OSFP-800G-2FR4, OSFP-2FR4-800G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
