Juniper Networks OSFP-DR8L-800G Compatible 800G Twin-port OSFP IHS/Finned Top Transceiver Module
Built for hosts recognizing OSFP-DR8L-800G, this HT-manufactured Twin-port OSFP IHS/Finned Top module delivers 800G transmission at 1310nm. Its rated reach is 100m, with Dual MTP/MPO-12 APC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OSFP-DR8L-800GHT Part Number: OSFP-DR8L-800G
Product Highlights
- Compatible alternative to Juniper Networks OSFP-DR8L-800G
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 100m
- Dual MTP/MPO-12 APC / SMF interface
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | OSFP-DR8L-800G |
|---|---|
| Manufacturer | HT |
| Form Factor | Twin-port OSFP IHS/Finned Top |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 100m |
| Connector | Dual MTP/MPO-12 APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -2.9~4.0dBm |
| Minimum Receiver Power | -5.9dBm |
| Power Budget | 3dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 17W |
| Extinction Ratio | >3.5dB |
| Modulation (Electrical) | 8x 100G-PAM4 |
| Modulation (Optical) | Dual 4x 100G-PAM4 |
| Packaging Technology | COB (Chip on Board) Packaging |
| Modulation Format | PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Inbuilt FEC | No |
| Protocols | OSFP MSA, IEE802.3ck, IEEE 802.3cu |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1310nm, rated reach 100m.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Finned Top housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 100m route. Keep the Dual MTP/MPO-12 APC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.9~4.0dBm; the stated optical power budget is 3dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
Compatibility testing for OSFP-DR8L-800G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-DR8L-800G, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Dual MTP/MPO-12 APC with SMF. The specified maximum reach is 100m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use OSFP-DR8L-800G as the compatibility cross-reference and OSFP-DR8L-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
