Generic OSFP-ZRH-800G Compatible 800G OSFP Transceiver Module
This Generic OSFP-ZRH-800G compatible transceiver provides 800G connectivity in a hot-swappable OSFP package. Its optical design operates at 1528.77~1567.13nm for up to Amplified: ≤120kmUnamplified: ≤64km, using Duplex LC/UPC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: OSFP-ZRH-800GHT Part Number: OSFP-ZRH-800G
Product Highlights
- Compatible alternative to Generic OSFP-ZRH-800G
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1528.77~1567.13nm
- Specified reach: Amplified: ≤120kmUnamplified: ≤64km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP-ZRH-800G |
|---|---|
| Manufacturer | HT |
| Form Factor | OSFP |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1528.77~1567.13nm |
| Max. Cable Distance | Amplified: ≤120kmUnamplified: ≤64km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Max. Power Consumption | 27W |
| Inbuilt FEC | OFEC |
| TX Power | -8~-1dBm |
| RX Power | Rx total input power: -30~7dBmAmplified: OIF 800ZR: -9~0dBmUnamplified: OIF 800ZR: -18~0dBm |
| DDM/DOM | Supported |
| Bit Error Ratio (BER) | Pre FEC: 3E-3Post FEC: 1E-15 |
| Modulation (Optical) | 16QAM |
| Modulation (Electrical) | 8x100G-PAM4 |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Application | Edge DCI |
| Protocols | OSFP MSA Rev5.0, IEEE 802.3-2022, OIF 800ZR, CMIS 5.2 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1528.77~1567.13nm, rated reach Amplified: ≤120kmUnamplified: ≤64km.
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a OSFP housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8~-1dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
Factory verification starts with the expected OSFP-ZRH-800G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is Amplified: ≤120kmUnamplified: ≤64km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use OSFP-ZRH-800G as the compatibility cross-reference and OSFP-ZRH-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
