Cisco QDD-400G-AE Compatible 400G QSFP-DD 8 x 50G PAM4 Active Electrical Cable
For equipment that specifies Cisco QDD-400G-AE, this HT-manufactured AEC family offers 400G direct-attach connectivity with QSFP-DD to QSFP-DD. Rather than treating different OEM length codes as interchangeable, the available configurations below link to their own product pages. Mechanical details, installation planning and factory checks are included for engineering and purchasing review.
Series Part Number: QDD-400G-AEHT Part Number: QDD-400G-AE
Product Highlights
- HT-manufactured compatible alternative for Cisco QDD-400G-AE
- 400G aggregate connectivity at 400Gbps
- Interface configuration: QSFP-DD to QSFP-DD
- Active DAC (AEC) / Copper
- Length configurations covered: 5m (16ft)
- Conductor specification: 28AWG
- Power consumption: 10W Per End
- Operating temperature: 0 to 70°C (32 to 158°F)
Available Lengths and Corresponding Part Numbers
The documented series configuration is 5m (16ft). Use the relevant OEM reference below together with the HT identity and required length when requesting a quotation. If another length carries a different OEM part number, it must be reviewed and ordered as that distinct configuration.
Compatible OEM Part Numbers
- QDD-400G-AE05
Specifications
| HT Part Number | QDD-400G-AE |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD to QSFP-DD |
| Max. Data Rate | 400Gbps |
| Media | Copper |
| Cable Type | Active DAC (AEC) |
| Minimum Bend Radius | 53mm |
| Wire AWG | 28AWG |
| Cable Length Options Covered | 5m (16ft) |
| Jacket Material | PET |
| Max. Power Consumption | 10W Per End |
| Modulation Format | 8x 50G-PAM4 |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP-DD MSA, IEEE 802.3cd, CMIS 5.0 |
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this series, keep the interface rate, AEC construction and length-specific OEM reference together throughout that review.
Applications and Deployment
Active electrical cables use signal recovery or retiming to support demanding high-speed electrical links. Deployment should begin with host support for the exact AEC configuration, followed by checks of per-end power, cooling and breakout operation. The two ends and cable are engineered and tested as one assembly. For this series, the listed interface is QSFP-DD to QSFP-DD and the aggregate rate is 400G.
Cable Construction and Routing
For this assembly, the conductor specification is 28AWG; the jacket material is PET; the minimum bend radius is 53mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 10W Per End. These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Cisco Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QDD-400G-AE identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Frequently Asked Questions
Is this an original Cisco cable?
No. It is an HT-manufactured compatible cable for equipment that specifies QDD-400G-AE, not an original Cisco-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this AEC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.
