Generic QDD-SR4.2-400G Compatible 400G QSFP-DD SR4.2 Transceiver Module
Built for hosts recognizing QDD-SR4.2-400G, this HT-manufactured QSFP-DD module delivers 400G transmission at 850nm,910nm. Its rated reach is 70m on OM3 / 150m on OM5, with MTP/MPO-12 (UPC) as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-SR4.2-400GHT Part Number: QDD-SR4.2-400G
Product Highlights
- Compatible alternative to Generic QDD-SR4.2-400G
- 400G connectivity at 425Gbps
- Optical wavelength: 850nm,910nm
- Specified reach: 70m on OM3 / 150m on OM5
- MTP/MPO-12 (UPC) / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QDD-SR4.2-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 425Gbps |
| Wavelength | 850nm,910nm |
| Max. Cable Distance | 70m@OM3/150m@OM5 |
| Connector | MTP/MPO-12 (UPC) |
| Media | MMF |
| Transmitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -6.5dBm~4dBm |
| Minimum Receiver Power | -8.5dBm |
| Power Budget | 2dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 12W |
| Extinction Ratio | 3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 8x50G-PAM4 |
| DSP | TX and RX |
| Inbuilt FEC | NO |
| Core Size | 50/125µm |
| Packaging Technology | COB |
| Protocols | QSFP-DD MSA, IEEE 802.3-2015 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 425Gbps, wavelength 850nm,910nm, rated reach 70m on OM3 / 150m on OM5.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 (UPC) interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 70m on OM3 / 150m on OM5 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-12 (UPC) mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5dBm~4dBm; the stated optical power budget is 2dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each QDD-SR4.2-400G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
Factory verification starts with the expected QDD-SR4.2-400G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use MTP/MPO-12 (UPC) with MMF. The specified maximum reach is 70m on OM3 / 150m on OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use QDD-SR4.2-400G as the compatibility cross-reference and QDD-SR4.2-400G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
