QSFP 112 to QSFP 112-400G-DAC-1M3FT 400G QSFP112 4 x 100G PAM4 Passive Copper Twinax Cable, 1m (3ft)
For a direct equipment connection requiring Generic QSFP 112 to QSFP 112-400G-DAC-1M3FT, this page supplies the 1m (3ft) version with QSFP 112 to QSFP 112. The cable supports 400G operation and eliminates a separate module-and-patch-cord assembly. Installation, maintenance and spare-cable identification are addressed alongside the full technical details.
OEM Part Number: QSFP 112 to QSFP 112-400G-DAC-1M3FTHT Part Number: QSFP 112 to QSFP 112-400G-DAC-1M3FT
Product Highlights
- HT-manufactured DAC assembly in 1m (3ft)
- 400G connectivity at 400Gbps
- Interface configuration: QSFP 112 to QSFP 112
- Fixed length and part number: 1m (3ft), QSFP 112 to QSFP 112-400G-DAC-1M3FT
- Cable construction: Passive Twinax
- Conductor specification: 26AWG
- Maximum power consumption: 0.1W Per End
- Minimum bend radius: 46mm
Specifications
| HT Part Number | QSFP 112 to QSFP 112-400G-DAC-1M3FT |
|---|---|
| Manufacturer | HT |
| Connector Type | QSFP 112 to QSFP 112 |
| Max. Data Rate | 400Gbps |
| Minimum Bend Radius | 46mm |
| Wire AWG | 26AWG |
| Cable Length | 1m (3.28ft) |
| Jacket Material | PET |
| Cable Type | Passive Twinax |
| Compatible | Generic |
| Max. Power Consumption | 0.1W Per End |
| Power Supply | 3.3V |
| Temperature | 0 to 70°C (32 to 158°F) |
| Application | 400G Ethernet |
| Modulation Technology | 4x106.25Gb/s PAM4 |
| Protocol | CMIS 5.0SFF-8024 |
Power and Thermal Planning
The rated power consumption is 0.1W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Network and Protocol Considerations
The intended application is 400G Ethernet.
Passive Copper Operation
A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.
Length Selection and Installation Planning
At 1m (3ft), QSFP 112 to QSFP 112-400G-DAC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Position Within the Length Range
QSFP 112 to QSFP 112-400G-DAC-1M3FT occupies the middle of this family between QSFP 112 to QSFP 112-400G-DAC-0.5M2FT at 0.5m (2ft) and QSFP 112 to QSFP 112-400G-DAC-1.5M5FT at 1.5m (5ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the listed conductor specification is 26AWG; the minimum bend radius is 46mm; the stated power consumption is 0.1W Per End; the jacket material is PET.
Cable Construction and Routing
This assembly uses 26AWG conductors, PET jacket, minimum bend radius 46mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Volume orders can include customer references on the labels and carton list.
Generic Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. The check includes link stability and diagnostic indications, followed by a final inspection of both ends.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. Quantity and any labeling instructions should be attached specifically to QSFP 112 to QSFP 112-400G-DAC-1M3FT.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
