Arista Networks QSFP-200G-FR4 Compatible 200G QSFP56 FR4 Transceiver Module
This Arista Networks QSFP-200G-FR4 compatible transceiver provides 200G connectivity in a hot-swappable QSFP56 package. Its optical design operates at 1271nm, 1291nm, 1311nm and 1331nm for up to 2km, using Duplex LC/UPC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: QSFP-200G-FR4HT Part Number: QSFP-FR4-200G
Product Highlights
- Compatible alternative to Arista Networks QSFP-200G-FR4
- 200G connectivity at 200Gbps (4x50Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 2km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Arista Compatible | QSFP-200G-FR4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-FR4-200G |
| Form Factor | QSFP56 |
| Max. Data Rate | 200Gbps (4x50Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max. Cable Distance | 2km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -4.2~4.7dBm |
| Minimum Receiver Power | -8.2dBm |
| Power Budget | 4dB |
| Receiver Overload | 4.7dBm |
| Max. Power Consumption | 6.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x50G-PAM4 |
| Modulation (Optical) | 4x50G-PAM4 |
| Protocols | IEEE 802.3cd, IEEE 802.3bs, QSFP56 MSA, SFF-8665, SFF-8024, SFF-8679 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 200Gbps (4x50Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 2km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 200G interface configuration must match the remote equipment; sharing a QSFP56 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 2km route. Keep the Duplex LC/UPC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.2~4.7dBm; the stated optical power budget is 4dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Arista Networks Compatibility and Factory Testing
The module is checked for host recognition as QSFP-200G-FR4, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-200G-FR4, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP-FR4-200G together with OEM reference QSFP-200G-FR4 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
