Juniper QSFP-4×10G-SR Compatible 10G QSFP+ SR Transceiver Module
This Juniper QSFP-4×10G-SR compatible transceiver provides 10G connectivity in a hot-swappable QSFP+ package. Its optical design operates at 850nm for up to 150m on OM4 / 100m on OM3, using MTP/MPO-12 Male. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: QSFP-4×10G-SRHT Part Number: QSFP-4×10G-SR
Product Highlights
- Compatible alternative to Juniper QSFP-4×10G-SR
- 10G connectivity at 41.25Gbps (4x 10.3125Gbps)
- Optical wavelength: 850nm
- Specified reach: 150m on OM4 / 100m on OM3
- MTP/MPO-12 Male / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-4×10G-SR |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP+ |
| Max. Data Rate | 41.25Gbps (4x 10.3125Gbps) |
| Wavelength | 850nm |
| Max. Transmission Distance | 150m@OM4/100m@OM3 |
| Connector | MTP/MPO-12 Male |
| Cable Type | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.6~-1dBm |
| Receiver Sensitivity | ≤-9.5dBm |
| Digital Optical Monitoring | Yes |
| Receiver Overload | 2.4dBm |
| Max. Power Consumption | ≤1.5W |
| Core Size | 50um |
| Extinction Ratio | >3dB |
| Modulation | NRZ |
| Host FEC | Supported |
| Modal Bandwidth | 2000 (OM3) MHz*km4700 (OM4) MHz*km |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3 40GBASE-SR4, QSFP+ MSA, SFF-8436 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 41.25Gbps (4x 10.3125Gbps), wavelength 850nm, rated reach 150m on OM4 / 100m on OM3.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 Male interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a QSFP+ housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m on OM4 / 100m on OM3 reach. Keep the MTP/MPO-12 Male end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.6~-1dBm; receiver sensitivity is ≤-9.5dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each QSFP-4×10G-SR compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Compatibility and Factory Testing
Factory verification starts with the expected QSFP-4×10G-SR identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-4×10G-SR, not an original Juniper-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 Male with MMF. The specified maximum reach is 150m on OM4 / 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP-4×10G-SR together with OEM reference QSFP-4×10G-SR and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
