QSFP-DD to QSFP-DD-800G-DAC-1M3FT 800G QSFP-DD 8 x 100G PAM4 Passive Copper Twinax Cable, 1m (3ft)
For a direct equipment connection requiring Generic QSFP-DD to QSFP-DD-800G-DAC-1M3FT, this page supplies the 1m (3ft) version with QSFP-DD to QSFP-DD. The cable supports 800G operation and eliminates a separate module-and-patch-cord assembly. Installation, maintenance and spare-cable identification are addressed alongside the full technical details.
OEM Part Number: QSFP-DD to QSFP-DD-800G-DAC-1M3FTHT Part Number: QSFP-DD to QSFP-DD-800G-DAC-1M3FT
Product Highlights
- HT-manufactured DAC assembly in 1m (3ft)
- 800G connectivity at 800Gbps
- Interface configuration: QSFP-DD to QSFP-DD
- Fixed length and part number: 1m (3ft), QSFP-DD to QSFP-DD-800G-DAC-1M3FT
- Cable construction: Passive DAC
- Conductor specification: 28AWG
- Maximum power consumption: 0.005W Per End
- Minimum bend radius: 81mm
Specifications
| HT Part Number | QSFP-DD to QSFP-DD-800G-DAC-1M3FT |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD to QSFP-DD |
| Max. Data Rate | 800Gbps |
| Media | Copper |
| Cable Type | Passive DAC |
| Cable Length | 1m (3ft) |
| Jacket Material | PVC (OFNR) |
| Minimum Bend Radius | 81mm |
| Wire AWG | 28AWG |
| Max. Power Consumption | 0.005W Per End |
| Modulation Format | 8x 100G-PAM4 |
| Commercial TemperatureRange | 0 to 70°C (32 to 158°F) |
| Application | 800G Ethernet |
| Protocols | QSFP-DD MSA, CMIS Rev4.0, IEEE 802.3ck |
Signal and Lane Configuration
The listed modulation format is 8x 100G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Network and Protocol Considerations
The intended application is 800G Ethernet. Listed interface and protocol references include QSFP-DD MSA, CMIS Rev4.0, IEEE 802.3ck. Confirm that the host firmware and port configuration support the same operating mode.
Passive Copper Operation
A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.
Length Selection and Installation Planning
At 1m (3ft), QSFP-DD to QSFP-DD-800G-DAC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Position Within the Length Range
QSFP-DD to QSFP-DD-800G-DAC-1M3FT occupies the middle of this family between QSFP-DD to QSFP-DD-800G-DAC-0.5M2FT at 0.5m (2ft) and QSFP-DD to QSFP-DD-800G-DAC-1.5M5FT at 1.5m (5ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the listed conductor specification is 28AWG; the minimum bend radius is 81mm; the stated power consumption is 0.005W Per End; the jacket material is PVC (OFNR).
Power and Thermal Planning
The rated power consumption is 0.005W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses 28AWG conductors, PVC (OFNR) jacket, minimum bend radius 81mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Volume orders can include customer references on the labels and carton list.
Generic Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. The check includes link stability and diagnostic indications, followed by a final inspection of both ends.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. QSFP-DD to QSFP-DD-800G-DAC-1M3FT refers here to 1m (3ft). Every other verified length has a separate part number and page in the length list.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. Quantity and any labeling instructions should be attached specifically to QSFP-DD to QSFP-DD-800G-DAC-1M3FT.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.
