NVIDIA/Mellanox QSFP-LX4-100G Compatible 100G QSFP28 LX4 Transceiver Module
The QSFP-LX4-100G compatible module serves equipment requiring a 100G QSFP28 interface with 1271nm,1291nm,1311nm,1331nm optics and a 2km on SMF / 100m on OM3 MMF rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: QSFP-LX4-100GHT Part Number: QSFP-LX4-100G
Product Highlights
- Compatible alternative to NVIDIA/Mellanox QSFP-LX4-100G
- 100G connectivity at 103.12Gbps (4x 25.78GGbps)
- Optical wavelength: 1271nm,1291nm,1311nm,1331nm
- Specified reach: 2km on SMF / 100m on OM3 MMF
- Duplex LC / SMF/MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-LX4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.12Gbps (4x 25.78GGbps) |
| Wavelength | 1271nm,1291nm,1311nm,1331nm |
| Max. Cable Distance | 2km@SMF/100m@OM3 MMF |
| Connector | Duplex LC |
| Media | SMF/MMF |
| Transmitter Type | CWDM4 DFB |
| Receiver Type | PIN |
| TX Power | -3~4.5dBm |
| Minimum Receiver Power | -7.3dBm |
| Power Budget | 4.3dB |
| Receiver Overload | 4.5dBm |
| Power Consumption | ≤4.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Inbuilt FEC | Yes |
| Packaging Technology | COB (Chip on Board) Packaging |
| Protocols | IEEE Std 802.3bm-2015, SFF-8665 Rev 1.9, SFF-8636 Rev 2.10a, SFF-8679 Rev 1.8 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 103.12Gbps (4x 25.78GGbps), wavelength 1271nm,1291nm,1311nm,1331nm, rated reach 2km on SMF / 100m on OM3 MMF.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 2km on SMF / 100m on OM3 MMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3~4.5dBm; the stated optical power budget is 4.3dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each QSFP-LX4-100G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
NVIDIA/Mellanox Compatibility and Factory Testing
Factory verification starts with the expected QSFP-LX4-100G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-LX4-100G, not an original NVIDIA/Mellanox-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF/MMF. The specified maximum reach is 2km on SMF / 100m on OM3 MMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP-LX4-100G, QSFP-LX4-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
