Dell Networking QSFP-PSM4-100G Compatible 100G QSFP28 PSM4 Transceiver Module
Built for hosts recognizing QSFP-PSM4-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 1310nm. Its rated reach is 500m on OS2, with MTP/MPO-12 APC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-PSM4-100GHT Part Number: QSFP-PSM4-100G
Product Highlights
- Compatible alternative to Dell Networking QSFP-PSM4-100G
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 1310nm
- Specified reach: 500m on OS2
- MTP/MPO-12 APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-PSM4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 500m@OS2 |
| Connector | MTP/MPO-12 APC |
| Media | SMF |
| Transmitter Type | 4x DFB |
| Receiver Type | PIN |
| TX Power | -9.4~2dBm |
| Minimum Receiver Power | -12.66dBm |
| Power Budget | 3.26dB |
| Receiver Overload | 2dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Packaging Technology | BOX Packaging |
| Bit Error Ratio (BER) | 1E-12 |
| MTBF | 1,868,530.214 Hours |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3‑2012，CAUI-4 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 1310nm, rated reach 500m on OS2.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 500m on OS2. Inspect every MTP/MPO-12 APC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9.4~2dBm; the stated optical power budget is 3.26dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Dell Networking Compatibility and Factory Testing
Factory verification starts with the expected QSFP-PSM4-100G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Dell Networking transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-PSM4-100G, not an original Dell Networking-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 APC with SMF. The specified maximum reach is 500m on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP-PSM4-100G, QSFP-PSM4-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
