Generic QSFP-ZR-100G-I Compatible 100G QSFP28 Transceiver Module
Built for hosts recognizing QSFP-ZR-100G-I, this HT-manufactured QSFP28 module delivers 100G transmission at C-Band 5THz DWDM Tunable. Its rated reach is 80km (unamplified)300km (amplified), with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-ZR-100G-IHT Part Number: QSFP-ZR-100G-S-I
Product Highlights
- Compatible alternative to Generic QSFP-ZR-100G-I
- 100G connectivity at 100Gbps
- Optical wavelength: C-Band 5THz DWDM Tunable
- Specified reach: 80km (unamplified)300km (amplified)
- Duplex LC/UPC / Duplex SMF interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-ZR-100G-S-I |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Data Rate | 100Gbps |
| Wavelength | C-Band 5THz DWDM Tunable |
| Distance | 80km (unamplified)300km (amplified) |
| Connector | Duplex LC/UPC |
| Media | Duplex SMF |
| Power Consumption | ≤6W |
| Management Interface | SFF-8636 |
| TX Power | -8~-4dBm |
| RX Power | -30~3dBm |
| Transmitter | Tunable |
| Receiver | Coherent |
| Client Side | 100GE Ethernet |
| Protocols | IEEE 802.3™-2022, 100GBASE-ZR, SFF-8636, SFF-8024 |
| Host Side FEC Mode | RS (528,514) |
| Line Side FEC Mode | SC |
| Host Side Modulation Format | NRZ |
| Line Side Modulation Format | DP- DQPSK |
| Relative Humidity | 5~95% (Non-condensing) |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 100Gbps, wavelength C-Band 5THz DWDM Tunable, rated reach 80km (unamplified)300km (amplified).
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8~-4dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
The module is checked for host recognition as QSFP-ZR-100G-I, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with Duplex SMF. The specified maximum reach is 80km (unamplified)300km (amplified), subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP-ZR-100G-I, QSFP-ZR-100G-S-I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
