Nokia QSFP-ZR-100G-S-I Compatible 100G QSFP28 Transceiver Module
This Nokia QSFP-ZR-100G-S-I compatible transceiver provides 100G connectivity in a hot-swappable QSFP28 package. Its optical design operates at C-Band 5THz DWDM Tunable for up to 80km (unamplified)300km (amplified), using Duplex LC/UPC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: QSFP-ZR-100G-S-IHT Part Number: QSFP-ZR-100G-S-I
Product Highlights
- Compatible alternative to Nokia QSFP-ZR-100G-S-I
- 100G connectivity at 100Gbps
- Optical wavelength: C-Band 5THz DWDM Tunable
- Specified reach: 80km (unamplified)300km (amplified)
- Duplex LC/UPC / Duplex SMF interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-ZR-100G-S-I |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Data Rate | 100Gbps |
| Wavelength | C-Band 5THz DWDM Tunable |
| Distance | 80km (unamplified)300km (amplified) |
| Connector | Duplex LC/UPC |
| Media | Duplex SMF |
| Power Consumption | ≤6W |
| Management Interface | CMIS |
| TX Power | -8~-4dBm |
| RX Power | -30~3dBm |
| Transmitter | Tunable |
| Receiver | Coherent |
| Client Side | OTN OTU4 |
| Protocols | IEEE 802.3™-2022, 100GBASE-ZR, CMIS, SFF-8024 |
| Host Side FEC Mode | RS (528,514) / RS (255,239) |
| Line Side FEC Mode | SC / RS (255,239) |
| Host Side Modulation Format | NRZ |
| Line Side Modulation Format | DP- DQPSK |
| Relative Humidity | 5~95% (Non-condensing) |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 100Gbps, wavelength C-Band 5THz DWDM Tunable, rated reach 80km (unamplified)300km (amplified).
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8~-4dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Nokia Compatibility and Factory Testing
The module is checked for host recognition as QSFP-ZR-100G-S-I, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Nokia transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ZR-100G-S-I, not an original Nokia-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with Duplex SMF. The specified maximum reach is 80km (unamplified)300km (amplified), subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP-ZR-100G-S-I, QSFP-ZR-100G-S-I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
