Juniper Networks QSFP-ZRBD-100G-S Compatible 100G QSFP28 Transceiver Module
Built for hosts recognizing QSFP-ZRBD-100G-S, this HT-manufactured QSFP28 module delivers 100G transmission at 1528.77~1566.72nm. Its rated reach is 80km (unamplified)300km (amplified), with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-ZRBD-100G-SHT Part Number: QSFP-ZRBD-100G-S
Product Highlights
- Compatible alternative to Juniper Networks QSFP-ZRBD-100G-S
- 100G connectivity at 100Gbps
- Optical wavelength: 1528.77~1566.72nm
- Specified reach: 80km (unamplified)300km (amplified)
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-ZRBD-100G-S |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 100Gbps |
| Wavelength | 1528.77~1566.72nm |
| Max. Cable Distance | 80km (unamplified)300km (amplified) |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | Coherent |
| Max. Power Consumption | 7W |
| TX Power | -8~-5dBm |
| Minimum Receiver Power | -31.5dBm |
| Power Budget | 23.5dB |
| Receiver Overload | 3dBm |
| DDM/DOM | Supported |
| Inbuilt FEC | Host: RS FEC or NoneMedia: SC FEC |
| Modulation (Electrical) | NRZ |
| Modulation (Optical) | DP-DQPSK |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Application | Ethernet、OTN |
| Protocols | SFF-8661 Rev.2.5, QSFP-DD MSA Rev 7.1, Type 2A, IEEE 802.3-2022, IEEE 802.3-2022 100GBASE-ZR, CMIS Rev5.2 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 100Gbps, wavelength 1528.77~1566.72nm, rated reach 80km (unamplified)300km (amplified).
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8~-5dBm; the stated optical power budget is 23.5dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as QSFP-ZRBD-100G-S, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ZRBD-100G-S, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 80km (unamplified)300km (amplified), subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use QSFP-ZRBD-100G-S as the compatibility cross-reference and QSFP-ZRBD-100G-S as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
