Arista QSFP112-DR4-400G Compatible 425G QSFP112 400GBASE-DR4 Transceiver Module
Built for hosts recognizing QSFP112-DR4-400G, this HT-manufactured QSFP112 module delivers 425G transmission at 1310nm. Its rated reach is 500m, with MPO-12/APC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP112-DR4-400GHT Part Number: QSFP112-DR4-400G
Product Highlights
- Compatible alternative to Arista QSFP112-DR4-400G
- 425G connectivity at 425Gbps (4x106.25Gb/s)
- Optical wavelength: 1310nm
- Specified reach: 500m
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP112-DR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP112 |
| Max. Data Rate | 425Gbps (4x106.25Gb/s) |
| Wavelength | 1310nm |
| Max. Cable Distance | 500m |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -2.9~4.0dBm |
| Minimum Receiver Power | -5.9dBm |
| Power Budget | 3dB |
| Receiver Overload | 4.0dBm |
| Max. Power Consumption | 10W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x100G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX and RX |
| Inbuilt FEC | No |
| Core Size | G.652/9um |
| Packaging Technology | COB |
| Protocols | QSFP112 MSA, CMIS 5.0, IEEE Std 802.3ck |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 425Gbps (4x106.25Gb/s), wavelength 1310nm, rated reach 500m.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 425G interface configuration must match the remote equipment; sharing a QSFP112 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 500m route. Keep the MPO-12/APC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.9~4.0dBm; the stated optical power budget is 3dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Arista Compatibility and Factory Testing
Factory verification starts with the expected QSFP112-DR4-400G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP112-DR4-400G, not an original Arista-branded module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 500m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP112-DR4-400G, QSFP112-DR4-400G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
