Broadcom QSFP112-FR4-400G Compatible 400G QSFP112 FR4 Transceiver Module
This Broadcom QSFP112-FR4-400G compatible transceiver provides 400G connectivity in a hot-swappable QSFP112 package. Its optical design operates at 1310nm for up to 2km, using Duplex LC/UPC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: QSFP112-FR4-400GHT Part Number: QSFP112-FR4-400G
Product Highlights
- Compatible alternative to Broadcom QSFP112-FR4-400G
- 400G connectivity at 425Gbps (4x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP112-FR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP112 |
| Max. Data Rate | 425Gbps (4x 106.25Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 2km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PD |
| TX Power | -3.2~4.4dBm |
| Minimum Receiver Power | -7.2dBm |
| Power Budget | 4dB |
| Receiver Overload | 4.4dBm |
| Max. Power Consumption | 10W |
| Extinction Ratio | ＞3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x100G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| Core Size | 9μm |
| Packaging Technology | COB |
| Protocols | QSFP-112 MSA, CMIS Rev 4.0, IEEE 802.3cu, OIF-CEI-112G-VSR-PAM4 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 425Gbps (4x 106.25Gbps), wavelength 1310nm, rated reach 2km.
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP112 housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.2~4.4dBm; the stated optical power budget is 4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Broadcom Compatibility and Factory Testing
Factory verification starts with the expected QSFP112-FR4-400G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Broadcom transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP112-FR4-400G, not an original Broadcom-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP112-FR4-400G together with OEM reference QSFP112-FR4-400G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
