Cisco QSFP112-SR4-400G Compatible 400G QSFP112 SR4 Transceiver Module
Built for hosts recognizing QSFP112-SR4-400G, this HT-manufactured QSFP112 module delivers 400G transmission at 850nm. Its rated reach is 30m on OM3 / 50m on OM4, with MPO-12/APC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP112-SR4-400GHT Part Number: QSFP112-SR4-400G
Product Highlights
- Compatible alternative to Cisco QSFP112-SR4-400G
- 400G connectivity at 425Gbps (4x106.25Gb/s)
- Optical wavelength: 850nm
- Specified reach: 30m on OM3 / 50m on OM4
- MPO-12/APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP112-SR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP112 |
| Max. Data Rate | 425Gbps (4x106.25Gb/s) |
| Wavelength | 850nm |
| Max. Cable Distance | 30m@OM3/50m@OM4 |
| Connector | MPO-12/APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -4.6~4dBm |
| Minimum Receiver Power | -6.4dBm |
| Power Budget | 1.8dB |
| Receiver Overload | 4.0dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | >2.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x100G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX and RX |
| Inbuilt FEC | Yes |
| Core Size | 50μm |
| Packaging Technology | COB |
| MTBF | 1420071 (@40°C, 90% CL) |
| Application | 400G Ethernet |
| Protocols | QSFP112 MSA, CMIS Rev5.0, IEEEdf-2024 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 425Gbps (4x106.25Gb/s), wavelength 850nm, rated reach 30m on OM3 / 50m on OM4.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP112 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 30m on OM3 / 50m on OM4 figure applies only under suitable cabling conditions. Inspect every MPO-12/APC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6~4dBm; the stated optical power budget is 1.8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as QSFP112-SR4-400G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP112-SR4-400G, not an original Cisco-branded module.
Which fiber and connector are required?
Use MPO-12/APC with MMF. The specified maximum reach is 30m on OM3 / 50m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify QSFP112-SR4-400G, QSFP112-SR4-400G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
