Ericsson RDH10250/3 Compatible 10G SFP+ LR Transceiver Module
Built for hosts recognizing RDH10250/3, this HT-manufactured SFP+ module delivers 10G transmission at the listed wavelength plan. Its rated reach is the stated reach, with LC duplex as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: RDH10250/3HT Part Number: SFP-10GLR-31-I
Product Highlights
- Compatible alternative to Ericsson RDH10250/3
- 10G connectivity at 10.3125Gbps
- LC duplex / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Ericsson Compatible | RDH10250/3 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLR-31-I |
| Form Factor | SFP+ |
| Max Data Rate | 10.3125Gbps |
| Connector | LC duplex |
| Cable Type | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -8.2~0.5dBm |
| Cable Distance | 10km |
| Power Budget | 6.2dB |
| Receiver Sensitivity | -14.4dBm |
| Power Consumption | ≤1W |
| Receiver Overload | 0.5dBm |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | IEEE 802.3ae, SFF-8431, SFF-8472, SFP+ MSA, SFF-8432, CPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10.3125Gbps.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Before commissioning, measure the complete single-mode channel against the stated budget for the rated distance. Inspect every LC duplex connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is -14.4dBm; the stated optical power budget is 6.2dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each RDH10250/3 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Ericsson Compatibility and Factory Testing
Factory verification starts with the expected RDH10250/3 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Ericsson transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies RDH10250/3, not an original Ericsson-branded module.
Which fiber and connector are required?
Use LC duplex with SMF. The specified maximum reach is the distance stated in the specifications, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use RDH10250/3 as the compatibility cross-reference and SFP-10GLR-31-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
