SC UPC Duplex OS2 Fiber Adapter with Flange, 10pcs/Pack
For Tanzanian site work, correct product selection should be followed by careful transport, connector inspection and retention of the fiber records. SC UPC Duplex OS2 Fiber Adapter with Flange couples two SC connectors into one continuous optical route. Inside the housing, a zirconia ceramic sleeve holds both ferrules on a common axis, keeping insertion loss low and reliably repeatable across hundreds of mating cycles. The flanged housing screws directly to the rack-mounted panel cutout for a permanent, vibration-proof mounting.
Product Highlights
- Protective Dust Cap Keeps Adapter’s Interior Clean from Dust
- Stainless Steel Clips for Tool-less Snap-in Installation
- Can be Used with M2 Model Screw
- ≤0.2dB (Typical) Low Insertion Loss
- Color Coded for Rapid Fiber Management
Specifications
| Connector Type | SC-SC |
|---|---|
| Body Style | Duplex |
| Polish Type | UPC |
| Fiber Mode | OS2 9/125μm |
| Insertion Loss | ≤0.2dB |
| Durability | 1000 times |
| Mounting Type | Full flanged |
| Color | Blue |
| Flammability Rate | UL 94V-0 |
| RoHS Compliancy Status | Compliant |
| Operating Temperature | -40 to 85℃(-40 to 185℉) |
| Storage Temperature | -10 to 60℃(14 to 140℉) |
Phosphor bronze and zirconia sleeves compared
Two sleeve materials dominate the optical adapter market. Zirconia ceramic sleeves give the tightest alignment and are the correct option for single-mode and high-operation multimode work, where core geometry leaves no room for eccentricity. Phosphor bronze sleeves serve legacy multimode and metallic-ferrule connectors where the tolerance specification is looser and the cost matters more. Matching the sleeve to the application keeps both operation and budget under control.
Bulk packs and the economics of sparing
Panel work consumes adapters in dozens, not singles: a frame reload takes a full pack, and the spares kit must hold more against breakage, contamination and the optical adapter that vanishes during a hurried re-entry. The ten-piece pack format matches that reality - one pack per panel location covers the load-out with spares, and the unit cost drops well below single-piece pricing. Bulk packs further guarantee that every adapter on the rack-mounted panel is the identical revision, the identical color and the identical sleeve quality.
Kit planning for panel installation
A disciplined panel installation kit counts everything before the van leaves: adapters at one pack per panel plus a spare, caps for every unused port, the screws or clips the rack-mounted panel needs, and the cleaning supplies that keep end faces serviceable. Adapters are the cheapest line on that list and the one whose absence stops the job outright. The bulk pack format makes the counting simple - two packs per location and the location is covered, installed and spared.
Panel cutouts and footprint discipline
Adapter panels are standardized around a handful of footprints, and the SC simplex footprint is the most common: duplex LC adapters are built to drop into the identical cutout, which is why LC and SC positions interchange freely on modern frames. Keeping to the standard footprint matters when a panel is re-loaded years later - the replacement adapter must fit the hole that is already there.
What adapter testing actually measures
An adapter contributes no signal of its own; thus, its test is a mating test: reference connectors mate through the optical adapter, and the inserted loss is recorded. A zirconia-sleeve adapter should add no more than 0.2 dB, and the mating must repeat that figure across cycles. Durability testing runs the mating hundreds of times and re-measures - a sleeve that wears loose announces itself as creeping loss. These figures, not the housing color, are what separates an adapter that serves for years from one that becomes the mystery fault.
Selecting the right adapter for the panel
Five decisions define the optical adapter order: the connector being used pairing should be matched to both sides of the mating, the mounting style must fit the rack-mounted panel cutout, the polish color code should be matched to the plant, the sleeve material must suit the operation grade, and the count must cover the load-out plus spares. Getting all five right at order time is what turns a bag of couplers into a dependable panel. Where the pairing crosses connector families, the hybrid range covers the common conversions.
Factory Quality Control and Testing
Every adapter is inspected before packing: the sleeve bore is checked for alignment and surface finish, the housing latches are cycled for positive engagement, and sample matings from each production lot are measured for insertion loss. Accessories are checked for fit against the adapters they serve. For Tanzanian site work, keep this requirement with the field checklist and the delivered product records.
Purchase and Factory Support
Refer to this adapter by connector pairing, mounting style, polish grade and pack number of units when purchasing a quotation. For configurations outside the listed options - mixed packs, panel hardware kits or project packaging - send the specification with the request and the factory will ensure the manufacturable specification. For Tanzanian deliveries, the order details should include any site identification needed by the installation team.
