Arista Networks SFP-10G-LRL Compatible 10G SFP+ LRL Transceiver Module
Built for hosts recognizing SFP-10G-LRL, this HT-manufactured SFP+ module delivers 10G transmission at 1310nm. Its rated reach is 2km, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10G-LRLHT Part Number: SFP-10GLRL-31
Product Highlights
- Compatible alternative to Arista Networks SFP-10G-LRL
- 10G connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Arista Networks Compatible | SFP-10G-LRL |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRL-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 2km |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | -8.2~-0.5dBm |
| Receiver Sensitivity | <-12.6dBm |
| Max. Power Consumption | ≤1.2W |
| Receiver Overload | +1.5dBm |
| Core Size | 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 2km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 2km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~-0.5dBm; receiver sensitivity is <-12.6dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each SFP-10G-LRL compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Arista Networks Compatibility and Factory Testing
Factory verification starts with the expected SFP-10G-LRL identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10G-LRL, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use SFP-10G-LRL as the compatibility cross-reference and SFP-10GLRL-31 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
