NETGEAR SFP-10G-T-30I Compatible 10G SFP+ T Transceiver Module
The SFP-10G-T-30I compatible module serves equipment requiring a 10G SFP+ interface with the listed wavelength plan optics and a 30m on Cat6a / Cat7 or Better rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: SFP-10G-T-30IHT Part Number: SFP-10G-T-30I
Product Highlights
- Compatible alternative to NETGEAR SFP-10G-T-30I
- 10G connectivity at 10Gbps
- Specified reach: 30m on Cat6a / Cat7 or Better
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-10G-T-30I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Max. Power Consumption | ≤2.5W |
| Max. Transmission Distance | 30m@Cat6a/Cat7 or Better |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Not Supported |
| MTBF | 5,000,000 Hours |
| EMC (Electro Magnetic Compatibility) | Supported |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
| Protocols | 10GBASE-KR, IEEE 802.3an, IEEE 802.3az, SFP+ MSA, SFF-8431 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, rated reach 30m on Cat6a / Cat7 or Better.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this copper interface, use the stated cable category and keep the channel within 30m on Cat6a / Cat7 or Better. Patch-cord construction, connector quality and auto-negotiation can affect the result. Verify the negotiated speed and diagnostics at both ends rather than assuming every RJ-45 port behaves identically.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each SFP-10G-T-30I compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
NETGEAR Compatibility and Factory Testing
Factory verification starts with the expected SFP-10G-T-30I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NETGEAR transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10G-T-30I, not an original NETGEAR-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 30m on Cat6a / Cat7 or Better, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
When ordering, specify SFP-10G-T-30I, SFP-10G-T-30I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
