Extreme Networks SFP-10G32-BX20 Compatible 10G SFP+ BX20-D Transceiver Module
Built for hosts recognizing SFP-10G32-BX20, this HT-manufactured SFP+ module delivers 10G transmission at 1330nm-TX/1270nm-RX. Its rated reach is 20km, with Simplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10G32-BX20HT Part Number: SFP-10G32-BX20
Product Highlights
- Compatible alternative to Extreme Networks SFP-10G32-BX20
- 10G connectivity at 10Gbps
- Optical wavelength: 1330nm-TX/1270nm-RX
- Specified reach: 20km
- Simplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP-10G32-BX20 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1330nm-TX/1270nm-RX |
| Max. Transmission Distance | 20km |
| Connector | Simplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -6~3dBm |
| Receiver Sensitivity | < -14.4dBm |
| Power Budget | 8.4dB |
| Receiver Overload | 0.5dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3.5dB |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1330nm-TX/1270nm-RX, rated reach 20km.
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
BiDi operation saves a fiber strand but makes wavelength orientation critical. Record the part installed at each end and check its paired receive wavelength. The 20km rating still depends on total channel loss, including connectors and splices.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6~3dBm; receiver sensitivity is < -14.4dBm; the stated optical power budget is 8.4dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Extreme Networks Compatibility and Factory Testing
Compatibility testing for SFP-10G32-BX20 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10G32-BX20, not an original Extreme Networks-branded module.
Which fiber and connector are required?
Use Simplex LC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify SFP-10G32-BX20, SFP-10G32-BX20, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
