Intel SFP-10GZRC-55 Compatible 10G SFP+ ZR Transceiver Module
Built for hosts recognizing SFP-10GZRC-55, this HT-manufactured SFP+ module delivers 10G transmission at 1550nm. Its rated reach is 100km, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10GZRC-55HT Part Number: SFP-10G-ZR100
Product Highlights
- Compatible alternative to Intel SFP-10GZRC-55
- 10G connectivity at 11.3Gbps
- Optical wavelength: 1550nm
- Specified reach: 100km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP-10G-ZR100 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1550nm |
| Max. Transmission Distance | 100km |
| Connector | Duplex LC |
| Transmitter Type | EML 1550nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 0~5dBm |
| Receiver Sensitivity | < -25dBm |
| Core Size | 9/125µm |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 11.3Gbps, wavelength 1550nm, rated reach 100km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1550nm, then include their insertion loss in the 100km power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -25dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each SFP-10GZRC-55 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Intel Compatibility and Factory Testing
Compatibility testing for SFP-10GZRC-55 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Intel transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GZRC-55, not an original Intel-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 100km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number SFP-10G-ZR100 together with OEM reference SFP-10GZRC-55 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
