SFP-DD to QSFP28-100G-AOC-7M23FT 100G SFP-DD 2 x 50G PAM4 to QSFP28 4 x 25G NRZ Active Optical Cable, 7m (23ft)
This 7m (23ft) AOC assembly is made for installations that call for Generic SFP-DD to QSFP28-100G-AOC-7M23FT at 100G. The SFP-DD to QSFP28 connectors and cable arrive as one complete product, ready for a direct link between suitable ports. Field-handling guidance, exact specifications and pre-packing functional checks apply to the part number shown here.
OEM Part Number: SFP-DD to QSFP28-100G-AOC-7M23FTHT Part Number: SFP-DD to QSFP28-100G-AOC-7M23FT
Product Highlights
- HT-manufactured AOC assembly in 7m (23ft)
- 100G connectivity at 100Gbps
- Interface configuration: SFP-DD to QSFP28
- Fixed length and part number: 7m (23ft), SFP-DD to QSFP28-100G-AOC-7M23FT
- Cable construction: OM3
- Maximum power consumption: SFP-DD: <3.5WQSFP28: <5.5W
- Minimum bend radius: 30mm
Specifications
| HT Part Number | SFP-DD to QSFP28-100G-AOC-7M23FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP-DD to QSFP28 |
| Max Data Rate | 100Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length | 7m (23ft) |
| Jacket Material | OFNP |
| Cable Type | OM3 |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Wavelength | 850nm |
| Power Consumption | SFP-DD: <3.5WQSFP28: <5.5W |
| Modulation (Electrical) | SFP-DD-2x 50G-PAM4 QSFP28-4x 25G-NRZ |
| Modulation (Optical) | 2x 50G-PAM4 |
| Power supply | 3.3V |
| DDM/DOM | Supported |
| Commercial Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP-DD & QSFP28 MSA, IEEE 802.3cd, RoHS6 (Lead-free) |
| Application | 100GBASE SR2 Ethernet |
Signal and Lane Configuration
The listed modulation format is SFP-DD-2x 50G-PAM4 QSFP28-4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
A 7m (23ft) run can remain tidy when its pathway and service allowance are planned together. Keep the integrated optical cable and both optical engines away from tight cable-tie pressure, verify bend control at changes of direction and ensure that neither port supports the assembly’s weight. Record the exact order code after acceptance. Within this family, SFP-DD to QSFP28-100G-AOC-5M16FT is shorter at 5m (16ft), while SFP-DD to QSFP28-100G-AOC-10M33FT is the next longer choice at 10m(33ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
SFP-DD to QSFP28-100G-AOC-7M23FT occupies the middle of this family between SFP-DD to QSFP28-100G-AOC-5M16FT at 5m (16ft) and SFP-DD to QSFP28-100G-AOC-10M33FT at 10m(33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the minimum bend radius is 30mm; the stated power consumption is SFP-DD: <3.5WQSFP28: <5.5W; the jacket material is OFNP.
Power and Thermal Planning
The rated power consumption is SFP-DD: <3.5WQSFP28: <5.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is 100GBASE SR2 Ethernet. Listed interface and protocol references include SFP-DD & QSFP28 MSA, IEEE 802.3cd, RoHS6 (Lead-free). Confirm that the host firmware and port configuration support the same operating mode.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Standard protective packing is used by default, with project documentation arranged when requested.
Generic Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. Keep SFP-DD to QSFP28-100G-AOC-7M23FT associated with 7m (23ft) throughout the order and receiving record.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.
