SFP-DD to SFP-DD-100G-AOC-20M66FT 100G SFP-DD 2 x 50G PAM4 Active Optical Cable, 20m (66ft)
The SFP-DD to SFP-DD-100G-AOC-20M66FT compatible AOC cable provides 100G connectivity for Generic equipment over a fixed 20m (66ft) assembly. Both ends use the stated SFP-DD to SFP-DD arrangement. It is inspected and functionally checked before packing, with handling guidance designed to protect the connectors during installation and later service.
OEM Part Number: SFP-DD to SFP-DD-100G-AOC-20M66FTHT Part Number: SFP-DD to SFP-DD-100G-AOC-20M66FT
Product Highlights
- HT-manufactured AOC assembly in 20m (66ft)
- 100G connectivity at 100Gbps
- Interface configuration: SFP-DD to SFP-DD
- Fixed length and part number: 20m (66ft), SFP-DD to SFP-DD-100G-AOC-20M66FT
- Cable construction: OM4
- Maximum power consumption: ≤3.5W
- Minimum bend radius: 60mm
Specifications
| HT Part Number | SFP-DD to SFP-DD-100G-AOC-20M66FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP-DD to SFP-DD |
| Max Data Rate | 100Gbps |
| Cable Length | 20m (66ft) |
| Cable Type | OM4 |
| Wavelength | 850nm |
| Minimum Bend Radius | 60mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Power Consumption | ≤3.5W |
| Power supply | 3.5V |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Modulation Format | 2x 50G-PAM4 to 2x 50G-PAM4 |
| DDM/DOM | Supported |
| Commercial Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP-DD MSA, SFP-DD MIS |
Signal and Lane Configuration
The listed modulation format is 2x 50G-PAM4 to 2x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Cable Construction and Routing
This assembly uses minimum bend radius 60mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP-DD MSA, SFP-DD MIS. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
This 20m (66ft) assembly is intended for routes that shorter members of the same family cannot serve comfortably. Before ordering, document the actual pathway and the space available for service access. During installation, secure the integrated optical cable and both optical engines without compressing it into an undersized bundle or leaving its weight suspended from the ports. Within this family, SFP-DD to SFP-DD-100G-AOC-15M49FT is shorter at 15m (49ft), while SFP-DD to SFP-DD-100G-AOC-25M82FT is the next longer choice at 25m (82ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
SFP-DD to SFP-DD-100G-AOC-20M66FT occupies the middle of this family between SFP-DD to SFP-DD-100G-AOC-15M49FT at 15m (49ft) and SFP-DD to SFP-DD-100G-AOC-25M82FT at 25m (82ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the minimum bend radius is 60mm; the stated power consumption is ≤3.5W.
Power and Thermal Planning
The rated power consumption is ≤3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Standard protective packing is used by default, with project documentation arranged when requested.
Generic Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Does this order code cover multiple lengths?
No. SFP-DD to SFP-DD-100G-AOC-20M66FT refers here to 20m (66ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. Keep SFP-DD to SFP-DD-100G-AOC-20M66FT associated with 20m (66ft) throughout the order and receiving record.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
