Extreme Networks SFP-GB-GE-T Compatible 1G SFP SGMII Transceiver Module 100m
This Extreme Networks SFP-GB-GE-T compatible transceiver provides 1G connectivity in a hot-swappable SFP SGMII package. Its optical design operates at the listed wavelength plan for up to 100m, using RJ-45. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: SFP-GB-GE-THT Part Number: SFP-GEB-T
Product Highlights
- Compatible alternative to Extreme Networks SFP-GB-GE-T
- 1G connectivity at 1000Mbps
- Specified reach: 100m
- RJ-45 / Cat 6/Cat 6a interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-GEB-T |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP SGMII |
| Max. Data Rate | 1000Mbps |
| Media | Cat 6/Cat 6a |
| Max. Cable Distance | 100m |
| Connector | RJ-45 |
| RX_LOS | NO |
| DOM Support | No |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | MSA Compliant, IEEE STD 802.3 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1000Mbps, rated reach 100m.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP SGMII housing alone does not make two transceiver types interoperable.
For this copper interface, use the stated cable category and keep the channel within 100m. Patch-cord construction, connector quality and auto-negotiation can affect the result. Verify the negotiated speed and diagnostics at both ends rather than assuming every RJ-45 port behaves identically.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Extreme Networks Compatibility and Factory Testing
Compatibility testing for SFP-GB-GE-T combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-GB-GE-T, not an original Extreme Networks-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Cat 6/Cat 6a. The rated reach is 100m, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
Use SFP-GB-GE-T as the compatibility cross-reference and SFP-GEB-T as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
