NETGEAR SFP-GE-BX Compatible 1G SFP Transceiver Module
Built for hosts recognizing SFP-GE-BX, this HT-manufactured SFP module delivers 1G transmission at 1310nm-TX/1490nm-RX. Its rated reach is 10km, with Simplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-GE-BXHT Part Number: SFP-1G34-BX10
Product Highlights
- Compatible alternative to NETGEAR SFP-GE-BX
- 1G connectivity at 1.25Gbps
- Optical wavelength: 1310nm-TX/1490nm-RX
- Specified reach: 10km
- Simplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| NETGEAR Compatible | SFP-GE-BX |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-1G34-BX10 |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Wavelength | 1310nm-TX/1490nm-RX |
| Max Cable Distance | 10km |
| Connector | Simplex LC |
| Optical Components | FP BiDi |
| Media | SMF |
| DOM Support | Yes |
| TX Power | -9~-3dBm |
| Receiver Sensitivity | < -20dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | Fast Ethernet, Gigabit Fibre Channel, MSA Compliant |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1.25Gbps, wavelength 1310nm-TX/1490nm-RX, rated reach 10km.
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
This single-fiber interface must be paired with the complementary wavelength direction. One end transmits on the wavelength the other receives. Verify connector polish and measure loss over the 10km design range before service.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9~-3dBm; receiver sensitivity is < -20dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
NETGEAR Compatibility and Factory Testing
The module is checked for host recognition as SFP-GE-BX, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NETGEAR transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-GE-BX, not an original NETGEAR-branded module.
Which fiber and connector are required?
Use Simplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use SFP-GE-BX as the compatibility cross-reference and SFP-1G34-BX10 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
