H3C SFP-GEB-T-IL Compatible 1G SFP SGMII Transceiver Module
Built for hosts recognizing SFP-GEB-T-IL, this HT-manufactured SFP SGMII module delivers 1G transmission at the listed wavelength plan. Its rated reach is 100m, with RJ-45 as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-GEB-T-ILHT Part Number: SFP-GEB-T-IL
Product Highlights
- Compatible alternative to H3C SFP-GEB-T-IL
- 1G connectivity at 1000Mbps
- Specified reach: 100m
- RJ-45 / Cat 5 interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-GEB-T-IL |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP SGMII |
| Max. Data Rate | 1000Mbps |
| Power Consumption | 1.2W |
| Max. Cable Distance | 100m |
| Connector | RJ-45 |
| RX_LOS | Yes |
| Media | Cat 5 |
| DOM Support | No |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP MSA Compliant, IEEE Std 802.3 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1000Mbps, rated reach 100m.
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
The rated 100m copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
H3C Compatibility and Factory Testing
Factory verification starts with the expected SFP-GEB-T-IL identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-GEB-T-IL, not an original H3C-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Cat 5. The rated reach is 100m, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Ordering Information
When ordering, specify SFP-GEB-T-IL, SFP-GEB-T-IL, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
