SFP+ to SFP+-10G-AOC-70M230FT 10G SFP+ Industrial Active Optical Cable, 70m (230ft)
The SFP+ to SFP+-10G-AOC-70M230FT compatible AOC cable provides 10G connectivity for Generic equipment over a fixed 70m (230ft) assembly. Both ends use the stated SFP+ to SFP+ arrangement. It is inspected and functionally checked before packing, with handling guidance designed to protect the connectors during installation and later service.
OEM Part Number: SFP+ to SFP+-10G-AOC-70M230FTHT Part Number: SFP+ to SFP+-10G-AOC-70M230FT
Product Highlights
- HT-manufactured AOC assembly in 70m (230ft)
- Interface configuration: SFP+ to SFP+
- Fixed length and part number: 70m (230ft), SFP+ to SFP+-10G-AOC-70M230FT
- Minimum bend radius: 30mm
Specifications
| HT Part Number | SFP+ to SFP+-10G-AOC-70M230FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP+ to SFP+ |
| Max Supply Voltage | 3.45 V |
| Minimum Bend Radius | 30mm |
| Cable Length | 1~300m@OM3 MMF |
| Wavelength | 850nm |
| Built-in CDR | NO |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Modulation | NRZ |
| Bit Error Rate | 1E-12 |
| Jacket Material | OFNP |
| Built-in FEC | NO |
| Protocols | SFF-8431,10GBASE Ethernet, Fibre Channel |
| Operation temperature | -40 to 85°C (-40 to 185°F) |
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
This 70m (230ft) assembly is intended for routes that shorter members of the same family cannot serve comfortably. Before ordering, document the actual pathway and the space available for service access. During installation, secure the integrated optical cable and both optical engines without compressing it into an undersized bundle or leaving its weight suspended from the ports. The next shorter verified assembly is SFP+ to SFP+-10G-AOC-50M164FT at 50m (164ft), which is the better comparison when the managed route leaves substantial unused cable.
Position Within the Length Range
SFP+ to SFP+-10G-AOC-70M230FT is the longest of 3 verified length options in this family. Compared with SFP+ to SFP+-10G-AOC-50M164FT at 50m (164ft), it provides 20m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.
Field Installation and Maintenance
Inspect the route and both connectors before installation, then support the cable without pulling on either connector housing. During maintenance, release the latch properly rather than using the cable as a handle. Keep protection on unused ends, and if the assembly is removed for later use, coil it loosely and record its part number so the same length can be returned to service. For this assembly, the minimum bend radius is 30mm; the jacket material is OFNP.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFF-8431,10GBASE Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.
Quality Assurance and Packaging
The cable and both connectors are inspected before a functional link test. Connector protection and bend-safe packing reduce handling damage during transport and storage. Customer or site labels can be added for field inventories, with different lengths separated to simplify issue and return of spare assemblies. Volume orders can include customer references on the labels and carton list.
Generic Compatibility and Factory Testing
A field-ready cable needs both correct identification and a stable operating link. Our pre-packing check therefore includes the connectors, host recognition and link behavior. For equipment with uncertain revision history, providing the host model and software release helps identify compatibility requirements before the assembly reaches the installation site. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
Ordering Information
Request the cable by its exact part number and length, and state the equipment model if compatibility confirmation is needed. Site orders can list quantities by rack or installation team. Any requested label should retain the part number so a removed or spare cable can still be identified accurately. Keep SFP+ to SFP+-10G-AOC-70M230FT associated with 70m (230ft) throughout the order and receiving record.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.
