Generic SFP1G-ZX120-55 Compatible 1G SFP Transceiver Module
This Generic SFP1G-ZX120-55 compatible transceiver provides 1G connectivity in a hot-swappable SFP package. Its optical design operates at 1550nm for up to 120km, using Duplex LC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: SFP1G-ZX120-55HT Part Number: SFP1G-ZX120-55
Product Highlights
- Compatible alternative to Generic SFP1G-ZX120-55
- 1G connectivity at 1.25Gbps
- Optical wavelength: 1550nm
- Specified reach: 120km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP1G-ZX120-55 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Wavelength | 1550nm |
| Max. Cable Distance | 120km |
| Connector | Duplex LC |
| Optical Components | DFB 1550nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 0~5dBm |
| Receiver Sensitivity | < -32dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | SFF-8472 MSA Compliant, IEEE 802.3ah-2004 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 1.25Gbps, wavelength 1550nm, rated reach 120km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1550nm, then include their insertion loss in the 120km power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -32dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
Factory verification starts with the expected SFP1G-ZX120-55 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 120km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use SFP1G-ZX120-55 as the compatibility cross-reference and SFP1G-ZX120-55 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
