Transition Networks TN-X2-10GB-LR Compatible XFP X2 10GBASE-LR Transceiver Module
The TN-X2-10GB-LR compatible module serves equipment requiring a XFP X2 interface with 1310nm optics and a 10km rating. Connection is through SC duplex. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: TN-X2-10GB-LRHT Part Number: TN-X2-10GB-LR
Product Highlights
- Compatible alternative to Transition Networks TN-X2-10GB-LR
- XFP connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km
- SC duplex / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Transition Networks Compatible | TN-X2-10GB-LR |
|---|---|
| Manufacturer | HT |
| HT Part Number | TN-X2-10GB-LR |
| Form Factor | X2 |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 10km |
| Connector | SC duplex |
| Transmitter Type | DFB 1310nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | -8.2~0.5dBm |
| Receiver Sensitivity | < -14.4dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 10km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a X2 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every SC duplex connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is < -14.4dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Transition Networks Compatibility and Factory Testing
Compatibility testing for TN-X2-10GB-LR combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Transition Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies TN-X2-10GB-LR, not an original Transition Networks-branded module.
Which fiber and connector are required?
Use SC duplex with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number TN-X2-10GB-LR together with OEM reference TN-X2-10GB-LR and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
