Juniper Networks XFP-10G-S Compatible XFP XFP 10GBASE-SR Transceiver Module
This Juniper Networks XFP-10G-S compatible transceiver provides XFP connectivity in a hot-swappable XFP package. Its optical design operates at 850nm for up to 300m over OM3 MMF, using LC duplex. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: XFP-10G-SHT Part Number: XFP-10GSR-85
Product Highlights
- Compatible alternative to Juniper Networks XFP-10G-S
- XFP connectivity at 10Gbps
- Optical wavelength: 850nm
- Specified reach: 300m over OM3 MMF
- LC duplex / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | XFP-10G-S |
|---|---|
| Manufacturer | HT |
| HT Part Number | XFP-10GSR-85 |
| Form Factor | XFP |
| Max. Data Rate | 10Gbps |
| Wavelength | 850nm |
| Max. Transmission Distance | 300m over OM3 MMF |
| Connector | LC duplex |
| Transmitter Type | VCSEL 850nm |
| Media | MMF |
| DOM Support | Yes |
| TX Power | -3.5~5.3dBm |
| Receiver Sensitivity | <-13dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 850nm, rated reach 300m over OM3 MMF.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The LC duplex interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a XFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 300m over OM3 MMF reach. Keep the LC duplex end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.5~5.3dBm; receiver sensitivity is <-13dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected XFP-10G-S identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies XFP-10G-S, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use LC duplex with MMF. The specified maximum reach is 300m over OM3 MMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number XFP-10GSR-85 together with OEM reference XFP-10G-S and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
